Fisher Scientific 650D Incubator, Thermo Fisher Scientific (CAT#: STEM-CC-1165-LGZ)

The manufacturer of Fisher Scientific 650D Incubator is Thermo Fisher Scientific. Model is 650D. The Fisher Scientific Isotemp 650D Incubator Gravity Flow Cycling provides precise routine laboratory procedures for heating, drying and staining slides, paraffin embedding, tissue culture work, incubation for antibody assays, microbial assays, crystallization studies, and more. The incubator has a built-in GFI outlet (120 v) for adding stirrers, hot plate stirrers, etc. The Fisher 650D has a temperature range of 30 °C to 75 °C (86 °F to 167 °F), and the keyboard control arrow keys are easy to use to increase or decrease the setpoint temperature in 0.1 °C increments. The overtemperature value is automatically set to 3 °C above the set value. The PID controller comes with fixed parameters and does not require tuning. The isothermal 650D incubator is low maintenance, the enamel coated steel cabinet is durable, equipped with stainless steel chamber, and low watt density heating elements.

Condition: used
Volume: 5.0 cu ft
Chamber Dimensions: 18 x 18 x 26.5 in
Case Material: Enamel coated Steel
Controller Type: Microprocessor
Temperature Range (Metric): 30 to 75 °C
Material (Internal): Stainless Steel
Temperature Uniformity: ±0.7 at 37 °C
Display: LED
Insulation: 3 in. Thick Fiberglass
Material: Steel
Resolution: 0.1 °C

1. Microprocessor control.
2. The controls are conveniently located on the top of the incubator.
3. Keypad with arrow keys to increase or decrease set point temperature in 0.1 °C increments.
4. The over-temperature value is automatically set to 3 °C higher than the set value.
5. The PID controller comes with fixed parameters, and tuning is not required.
6. Circuit breaker protects the incubator from power surges; battery backup.
7. Designed to stack two units.
8. Big three-character LED display.
9. The figures show the actual temperature to the nearest 0.1 °C.
10. The display shows the current value of the set point temperature.
11. The HEAT indicator cycles on and off when the incubator heater is on.
12. When the temperature exceeds the over-temperature limit, the alarm indicator light is on; the backup controller maintains the temperature at 3°C ​​higher than the set value; the software has built-in safety backup.
13. Small, medium and large workload capacity.
14. Available in three-chamber capacity.
15. Mounting holes at 2 inches. (5 cm) spaced room walls to place shelves.
16. The small incubator can hold up to 5 racks, the medium incubator can hold up to 8 racks, and the large incubator can hold up to 11 racks.
17. Low maintenance incubator inner and outer doors.
18. Cabinets have a durable enamel coated steel look.
19. Extruded aluminum finish with acrylic powder coating.
20. The box is made of easy-to-clean stainless steel.
21. Low watt density heating element design for long life.
22. Outer door and 3" silicone gasket. Thick (7.6 cm) fiberglass insulation prevents heat loss throughout.
23. The outer door opens 180° for unimpeded entry and features two gripper latches.
24. Tempered glass inner door.
25. Steel shelves 17.37 inches. wide, 16.75 inches. Front to back (44 x 42.5cm).
26. Black synthetic rubber feet keep the incubator from sliding and allow ventilation space between the incubator and the benchtop.

Being Instruments BIC-60C Cooling Incubator, Being Instruments(CAT#-STEM-CC-2173-LGZ)
Being Instruments BIO-150RHP CO2 Incubator, Being Instruments(CAT#-STEM-CC-2174-LGZ)
Being Instruments BIO-190RHP CO2 Incubator, Being Instruments(CAT#-STEM-CC-2175-LGZ)
Being Instruments BIO-240RHP CO2 Incubator, Being Instruments(CAT#-STEM-CC-2176-LGZ)
Being Instruments BIO-80RHP CO2 Incubator, Being Instruments(CAT#-STEM-CC-2177-LGZ)
Benchmark Scientific BSH1001 Dry Bath Incubator, Benchmark Scientific(CAT#-STEM-CC-2178-LGZ)