Beckman L-80XP Ultracentrifuge, 1,000 to 80,000 RPM, Beckman Coulter (CAT#: STEM-LCPO-0101-LGZ)

Advanced Technology and Ease of Use Thanks to an advanced on-board computer, powerful Optima eXPert software and easy-to-use touchscreen, the Optima L-XP offers superior functionality, optimized user efficiency, and more than any other Beckman has introduced to date Supercentrifuge for faster turnaround!

Optima eXPert software provides unprecedented centrifugal power. It helps you develop the most efficient centrifugation method, select rotors and laboratory instruments for a given application, and then simulate the results before performing protein and subcellular particle separations

The Optima L-XP uses state-of-the-art materials and technologies to achieve the high performance required - up to 100,000 rpm - to stretch the boundaries of research. Additionally, the air-cooled design of our drives provides the most energy efficient ultracentrifugation system ever. And the unbalance-resistant Optima L-XP drives can safely accommodate up to 10% under or over ducting.

Condition: certified pre-owned
Approximate Acceleration Time: 10 acceleration profiles–9 slow rates or maximum acceleration from 0 to set speed
Approximate Deceleration Time: 11 deceleration profiles–9 slow rates, coasting to a stop without brake, or full dynamic braking from set speed
Electrical Requirements 50 Hz, 220-240 VAC
Imbalance Tolerance: ±5 ml or 10%, whichever is greater
Maximum Heat Dissipation into Room under Steady-State Conditions: 1.0 kW (3,400 Btu/hr)
Noise Level 1 Meter in Front of Centrifuge: < 53 dBA
Set Speed: Actual rotor speed ± 10 rpm of set speed after equilibration (above 1,000 rpm)
Set Temperature: 0 to 40°C in 1°C increments
Set Time: To 999 hr 59 min; Hold for continuous runs
Speed Range: 1,000 to 80,000 rpm
Temperature Control: ± 0.3°C of set temperature (after equilibration)
Ambient Temperature Range: 10 to 40°C ambient
Clearances Required: 5.1 cm (2.0 in) sides; 15.2 cm (6.0 in) rear
Humidity Restrictions: < 95% (noncondensing)
Pollution Degree: 2
Time — Actual Display: Indicates time remaining in timed runs, time elapsed in Hold runs, or estimated time remaining in ?2t runs
Vacuum: Below 5 microns (0.7 Pa)
Finish: Control panel: coated polycarbonate. Top surface: urethane paint. Other surfaces: general purpose paint.
Installation Category: Category II
Display: Shows the accumulated ?2t to two significant digits (in exponential notation)
Top Surface: Urethane paint
Keypad Material: Coated polycarbonate
Manual Operation: Indicates time remaining in timed runs, time elapsed in Hold runs, or estimated time remaining in Ω2t runs
Set w²t: Up to 9.99 × 10^14 radians squared per second
Temperature Display Actual rotor temperature in 0.1°C increments

Easy-to-use expert software
Maximum speed: 80000 rpm
Tolerates unbalanced drives
Provide installation and training of Beckman training engineers
CFC-free refrigeration

Sorvall RC-3B Plus High Capacity Centrifuge, Often Paired With H6000A 6 x 1 Liter Rotors, Thermo Scientific (CAT#-STEM-LCPO-0067-LGZ)
Sorvall RC-3B Superspeed Centrifuge, Thermo Scientific (CAT#-STEM-LCPO-0068-LGZ)
Sorvall RC-3C Plus High Capacity Centrifuge, Thermo Scientific (CAT#-STEM-LCPO-0069-LGZ)
Sorvall RC-5B Plus Superspeed Centrifuge, 21,000 RPM, Thermo Scientific (CAT#-STEM-LCPO-0070-LGZ)
Thermo Scientific Sorvall RC 12BP Plus Large Capacity Centrifuge, -10°C to +40°C, Thermo Scientific (CAT#-STEM-LCPO-0071-LGZ)
Beckman Avanti J-25 Centrifuge, Beckman Coulter (CAT#-STEM-LCPO-0072-LGZ)